home *** CD-ROM | disk | FTP | other *** search
/ Ham Radio 2000 #2 / Ham Radio 2000 - Volume 2.iso / HAMV2 / PACKET / APRS805 / README / HELP.TXT < prev    next >
Text File  |  1997-11-24  |  50KB  |  917 lines

  1. HELP.TXT 8.0             APRS HELP DOCUMENT
  2.  
  3. All APRS documentation is in the form of individual text files in the
  4. APRS\README directory.  For an index, just use the DOS DIR command.
  5.  
  6. There are a few special versions of APRS which were derived from APRS74
  7. for special applications:       
  8.  
  9.        APRSdr.exe   Has a dead reckoning path following mode.  See DR.txt
  10.        APRSmin.exe  A minimized version 316K vice 373K (without DX & WX)
  11.        APRtrak.exe  A version for SPACE donated to AMSAT.  See SPACE.txt
  12.        APRSair.exe  A version that will plot airlines.  See AIRCRAFT.txt
  13.        APRSlink.exe Can crosslink POSITS between 2 TNC's on 2 freqs or
  14.                     between the PACSAT downlink and normal APRS nets
  15.        APRSnet.exe  Plots all APRS nationwide live on the internet and
  16.                     is current with APRS797.
  17.  
  18. APRS PACKET PROTOCOL:  APRS captures 4 types of packets used in real-time 
  19. tactical communications for display on its various screens as listed below:  
  20. For more detail see PROTOCOL.TXT
  21.  
  22.    POSITS   - Position reports (both STATION and OBJECTS, WX, etc)
  23.    MESSAGES - Includes messages and Bulletins
  24.    STATUS   - Status packets (any packet not a Posit, or Msg, or Spcl 
  25.    SPECIAL  - Acks, Queries, Pings, etc...
  26.  
  27. STARTUP:  APRS prompts new users for most important setup information.  But 
  28. there are two additional commands necessary.  These are INPUT-MY-POSIT and 
  29. INPUT-MY-STATUS.   See the INPUTS section further in this text.
  30.  
  31. APRS COMMANDS:  Most APRS commands are single keys which are active from 
  32. all display pages.  The first Help page (F1-HELP), defines all command 
  33. characters.  Many keys bring up additional command sub-menu's on the bottom 
  34. of the screen.  Just hit the first letter of any command listed in the 
  35. prompt.   In most prompts, the ENTER key will select the default choice 
  36. or complete the prompt with no action.  If a mouse driver is loaded, the 
  37. mouse can be used to move the cursor.  
  38.  
  39. The following section summarizes all of the TOP-LEVEL APRS command keys.
  40. the F1-HELP key will give you an on-screen summary or you can print the
  41. KEYS.TXT file for a nice one page reference.  First are the twelve major 
  42. display screens accessed by their first letter:
  43.  
  44. SCREENS           DESCRIPTION
  45. ---------------   ------------------------------------------------------
  46. L-LATEST STATUS - Latest STATUS beacon from each station
  47. B-BULLETINS     - Bulletins posted by other stations
  48. P-POSITIONS     - Position packets from all stations and objects
  49. H-HEARD LOG     - Number of packets per hour per station
  50. R-READ MSGS     - Displays your incomming and outgoing messages
  51. T-TRAFFIC       - Last 23 lines of traffic heard between other stations
  52. D-DIGIs USED    - Digi paths used by all stations (or DX message list)
  53. A-ALL BCNS      - Chronological log of all beacons, messages (or DX spots)
  54. V-VIEW          - Scrolling screen of all live packets
  55. alt-T           - TELEMETRY screen for the MIM module (see TELEMTRY.txt)
  56. SPACE BAR       - Displays the MAP of all stations and objects
  57. Y-Yaxis         - A quasi-3D view of the map
  58.  
  59. MENUs          DESCRIPTION
  60. ------------   ---------------------------------------------------------
  61. F1-HELP      - HELP Menu with several screens
  62. C-CONTROLS   - For switching on/off many APRS control functions
  63. F-FILES MENU - For loading, saving, PRINTing and/or replaying files
  64. I-INPUT MENU - For inputing your POSIT, OBJECTS and DF bearings
  65. M-MAP MENU   - For most MAP functinos
  66. O-OPERATIONS - Various commands involved in communications and keyboard ops
  67. W-WEATHER    - All commands dealing with entering and displaying weather
  68.  
  69. MESSAGE COMMANDS
  70. --------------------------------------------------------------------------
  71. R-READ MSGS  - Displays all incomming and outgoing messages
  72. E-ERASE (TO) - Erase outgoing messages TO other stations
  73. K-KILL (FROM)- Kill incomming lines FROM other stations
  74. S-SEND       - Send a message line
  75. T-TRAFFIC    - Display the latest 23 lines monitored between other stations
  76. F2-REPLY     - Reply to the last incoming message
  77.  
  78. SPECIAL KEYS
  79. -------------------------------------------------------------------------
  80. G-GOTO ME/TRK- Moves cursor immediately to your stn or to the TRACKED stn
  81. J-JUST ONE   - Will display Just one type of station
  82. N-NEXT WX    - Will move cursor to the next WX stn and display condx
  83. Q-QUIT       - Quit APRS.  Your POSIT will remain in your TNC BText
  84. U-UNPROTO    - Used to set your UNPROTO path
  85. X-XMT PKTS   - Transmits all or some of your outstanding packets
  86.  
  87. CURSOR and MAP KEYS
  88. -------------------------------------------------------------------------
  89. SPACE bar    - Redraws current map
  90. Arrows       - Moves cursor.  SHIFT Arrows (white) moves 5 times faster
  91. Home         - Homes the screen to the cursor location
  92. PgDn/Up      - ZOOMs the display in/out.  CTRL-PgUp/Dn zooms by 8
  93. End          - Moves map to your default location
  94. 1,3,5,7,9    - 1 gets default map.  3-9 reload maps saved in 3-9 keys
  95. ENTER or +/- - Hook/Unhook (select) a station. +/- cycle through all stns
  96.                Use < and > to cycle through only the stations on the screen
  97.                (actually, use the "," and"." keys to avoid holding SHIFT.)
  98. [ ]          - More or Fewer Lables on maps.  Also works with MAPS-BORDERS
  99.  
  100. SPECIAL FUNCTIONS
  101. -------------------------------------------------------------------------
  102. TAB - Displays status of most CONTROLS and SETUP items
  103. F1  - Help Menu with several screens
  104. F2  - Reply to message.  Pre-loads CALL from last message received
  105. F3/4- OBSOLETE.  Used to be More or Fewer Lables on maps.  
  106. F5  - Mark a FADE point during the Fade-circle DF technique
  107. F6  - ZERO out your SPEED, so when you QRT, others will not DR you.
  108. F7  - Toggle between 25 and 43 line text mode
  109. F8  - In GPS/HSP mode will get and plot an immediate fix
  110. F9  - Center map and scale to show ALL stations
  111. F10 - DOZ mode. Disables all screen writes so works better in WINDOWS
  112.  
  113. ALTERNATE KEYS
  114. ------------------------------------------------------------------------
  115. alt-S - SETUP menu and configuration save commands
  116. alt-T - Telemetry screen.  See TELEMTRY.txt
  117.  
  118. MOUSE:  Moves the cursor on the MAP and L/Plists.  See MOUSE.txt.
  119.  
  120.  
  121. FURTHER DETAILS ABOUT DISPLAYS:  The POSITS page (and the derived HEARD
  122. and DIGIpaths page) can have up to 9 pages or about 144 stations with
  123. new stations added on the last page.  Beyond this number, old stations 
  124. get bumped off the top of page 1.  If you occassionally use the FILES-ORDER
  125. command to sort the order of the stations, then the oldest will always
  126. be at the beginning and the most recent on the higher pages.  PgUp and PgDn 
  127. keys cycle through multiple pages.  Move the cursor and hit ENTER to select 
  128. a single station and get a prompt for a variety of actions.  Here are more 
  129. detail descriptions:
  130.  
  131.   L - LATEST STATUS shows the latest STATUS packet from each station.  This
  132.       screen is like a one-line broadcast message display.  In DX mode, this
  133.       screen lists the latest command from all stations on your local cluster.
  134.  
  135.   B - BULLETINS  shows the latest 42 BULLETINS.  See SEND command.
  136.  
  137.   P - POSITIONS shows the latest POSITION packet from each station.  
  138.       You may select (HOOK) any station or object in this list 
  139.       for additional commands shown below.  See the section on OBJects.   
  140.       Also the JUST ONE command will display, print or save JUST one type 
  141.       of station at a time.
  142.         Uplink - Uplink or quit uplinking that object
  143.         Move   - Move it anywhere else on the map
  144.         HOME   - Center the map on the object
  145.         Delete - Deletes the object from your list
  146.         Follow - Forces an OBJ to follow a purple path (APRSdr.exe only)
  147.         Kill   - Kills your uplinked object on EVERYONE's screens! 
  148.         Track  - Will keep the map centered on the TRACKED station
  149.         Alarm  - Will cause alarms if the marked station moves
  150.         Special- Marks the station for isolated display using JUST-SPECIAL
  151.  
  152.   H - HEARD LIST shows the number of packets per station per hour. 
  153.  
  154.   T - TRAFFIC screen shows the last 42 messages heard between other stns.
  155.       In DX mode, also collects TALK messages between DX cluster users.
  156.  
  157.   D - DIGIPEATER PAGE shows the raw packet headers including the digi-
  158.       peaters of stations on your LATEST list.  Proper use of digis is 
  159.       very important for minimizing QRM on APRS nets.  A * in the left 
  160.       column show stations heard DIRECT (maybe only once).  In DX mode, 
  161.       the D screen accumulates the list of all ACTIVE DXcluster MESSAGES.
  162.  
  163.   A - ALL PACKETS display shows a chronological history of all packets
  164.       including your own incoming and outgoing message lines.  Since 
  165.       messages do not have a time of receipt appended to them, this 
  166.       display is useful for seeing approximately when a message line 
  167.       was received.  In DX mode, this screen accumulates all DX/WX/WWV 
  168.       spots and announcements.
  169.  
  170.   F1- HELP gives a menu of several different pages of HELP including reading
  171.       any of the README files.  Other HELP screens:
  172.  
  173.       DIGIS   - one screen on how to use APRS DIGIPEATERS
  174.       FILES   - Read the README files on line (lots of them!)
  175.       HELP    - List of all APRS Commands
  176.       INFO    - Additional helpful info
  177.       NEW     - New-user simplified help screen
  178.       SYMBOLS - Shows all APRS symbols
  179.       VALID   - How to validate your copy of APRS
  180.  
  181. OBJECTS: APRS displays two types of symbols on its maps.  The station ICON of
  182. each APRS station or TNC and any OBJECTS placed on the map by any station
  183. using the INPUT-ADD command.  Once on the screen, the object is listed in 
  184. the P-list with a (+) symbol.  This means it will be transmitted by your 
  185. station.  You can stop UPLINKING each object by hooking it on the P-list and 
  186. toggle the U key.  Un-validated users are limited to uplinking only one 
  187. object.  If you delete the object from your screen, or toggled off the 
  188. UPLINK, it still remains on all screens in the network until each individual 
  189. operator deletes it.  Or you may select to delete from all screens which
  190. means your station will continue to transmit the object, but with a special 
  191. KILL mark on it.  It will disappear from all maps, but it will REMAIN in 
  192. everyone's PList.  If an object has not been updated in over two hours, 
  193. it fades to a dark gray color.
  194.  
  195.  
  196. MAP SYMBOL COLORS:  Several colors are used to differentiate the status of
  197. each station or object on the MAP display:
  198.            WHITE     - Active APRS stations on line 
  199.            GRAY      - TNC-only posit with no APRS message capability
  200.            YELLOW    - Objects that you are reporting (uplinking)
  201.            VIOLET    - Objects uplinked by other stations 
  202.            BLACK     - Positions older than 2 hours 
  203.            GREEN     - WIDE-RELAY digipeaters
  204.            BLUE      - Weather stations
  205.            CYAN      - Dead Reckoned positions
  206.            DARK BLUE - Old POSIT or track history
  207.  
  208. MAP COMMANDS AND FUNCTIONS:  These are display commands but there is a 
  209. complete MAPS menu of additional display options.
  210.  
  211.   SPACE  - Re-displays the current map and resets all display defaults.
  212.   
  213.   JUST   - Selects subsets of symbols to be displayed. JUST SPECIAL 
  214.            displays only the objects marked special on the P-list.  
  215.            JUST CALLS displays all objects but only the calls
  216.            of those marked SPECIAL.  Just PRINT will print all of 
  217.            a selected subset of objects to the printer.
  218.  
  219.   ESC    - Escapes the cursor from never-never land to the screen center
  220.  
  221.   1,3,5,9- Map memories for saving particular maps of interest to you.  
  222.            Use the MAP-SAVE command and one of these keys to recall any 
  223.            saved map.  The 1 key always has the USA map.
  224.            Save a CONFIG file to make these permanent.
  225.  
  226.   F9     - CENTER ALL CONTACTS.  Chooses a map to display ALL objects.
  227.   
  228.   HOOK   - Hook is a Navy term for selecting an object on a radar screen.
  229.            Use ENTER to hook an object at the cursor.  To step through all
  230.            stations, use the +/- keys.  Move the hooked station by moving 
  231.            the cursor to the new location and hitting the INSERT key or it 
  232.            can be removed using the DELETE key.  To prevent inadvertent 
  233.            movement of objects, a second ENTER key UNHOOKS.  Use the <> 
  234.            keys to cycle through all stations on the current map. (you
  235.            dont even need to hold down the shift key for these).
  236.   
  237.   INSERT - Relocates a HOOKED object on the screen.
  238.  
  239.   [ ]    - These keys display more or fewer labels on the maps or
  240.            more/fewer Borders during the maps-plots Borders command.
  241.  
  242. DEAD RECKONING:  For moving stations, APRS draws a small gray anchor circle 
  243. at the last posit, and then dead-reckons the light blue symbol ahead to the 
  244. estimated position.  Defeat this with CONTROLS-DR.  To hook a dead reckoned 
  245. station, hook the anchor circle, not the symbol itself.  There is also a 
  246. separate program called APRSdr.exe which can dead reckon objects around a 
  247. known course.  This is very useful for tracking known events such as
  248. runners in a marathon.  See DR.txt.  If DR'ing is messing up, then your PC
  249. clock is not sync'ed to GPS time.  Hit alt-S-GPS-TIME command and your PC
  250. MINUTES will be sync'ed to the next raw GPS posit that comes in...
  251.  
  252.  
  253. MAP MENU COMMANDS:  The following commands pertain to special functions
  254. regarding the map display.
  255.  
  256.   C - CONFIGURATION.  Has several sub commands:
  257.  
  258.       B - BACKGROUND.  Changes Background color.  Used to be TINT command.
  259.  
  260.       C - CHANGE-MAPLIST:  This is the most important map command for a new 
  261.       user.  It allows you to chose the MAPLIST.xxx for your area.  APRS 
  262.       uses this list to select each map based on your cursor location.
  263.       Currently APRS is distributed as EASt, SEast, MIDwest, CENtral,WESt 
  264.       NEAngland and EURopean versions.  The default MAPLIST.USA only points 
  265.       to major US and regional maps.  NOTE: When you use this command, 
  266.       the cursor will move to the center of the selected MAPLIST.xxx area.  
  267.       If you want to return the cursor to your current map screen, use 
  268.       the ESC key which always returns the cursor to the center of the 
  269.       current display.
  270.  
  271.       L - LIST-MAPLISTS.  Lists all the MAPLISTS in your MAPLISTS dir
  272.  
  273.       O - OFFSET-DATUM.  Allows you to offset your map a little to match 
  274.           your known GPS position with the datum used in your maps.
  275.  
  276.       S - SHOW-MAPS-LOADED.  Shows all of the APRS distributions that you
  277.           have loaded in your MAPS directory by listing the .TXT files.
  278.  
  279.   F - Toggle Features on/off such as Boundaries, Headings, Roads, Calls, 
  280.       Waterways, etc.  ALL features can also be turned on/off at once.  
  281.       Useful for very slow PCs where turning off all features still shows 
  282.       packet stations but without taking 20 seconds to re-draw map features.
  283.       The DIM command changes the intensity of the colors AND reverses 
  284.       color of replayed tracks so they work better using SCREEN-PRINT.
  285.  
  286.   H - Hierarchy:  This is an improvement on the BORDERS command since it
  287.       colors in the maps in the same sequence as they are listed in the
  288.       MAPLIST.xxx file.  The overlapping colors show the effect of the
  289.       sequence of this list.  Look carefully and you can figure out
  290.       overlap and out-of-order problems.
  291.  
  292.   L - Locks the current map to defeat the normal APRS auto-map selection.
  293.       Useful to avoid interrupting your current map if your cursor gets over
  294.       on another map during a special event.
  295.  
  296.   O - OVERLAYS  Overlays many data files over the current map:
  297.       DIGIS     Overlays allAPRS digis and their ranges.
  298.       GATES     Overlays all known HF gates
  299.       FREQS     Overlays all known APRS frequencies in use
  300.       NWS       Overlays the locations of all National WX sites.
  301.       PREVIOUS  Overlays previous (larger) map
  302.       OTHER     Overlays any other file in the XXXX.POS format
  303.  
  304.   P - PLOTS.  Select from a number of different plots:
  305.       Borders - Shows borders of all MAPS in the MAPLIST.xxx file.  You
  306.                 must use [ ] to select the size maps to display.  If a 
  307.                 map border appears, but the map does not come up as you zoom 
  308.                 in, then the MAP file is listed too early in the MAPLIST 
  309.                 and a later map overlaps its area.  If the map is missing, 
  310.                 APRS will BEEP.  If the Map file exists but its border does 
  311.                 not show up, then the file is not listed in the MAPLIST.xxx 
  312.                 file. 
  313.  
  314.       CAPgrid - Overlays Civil Air Patrol search-and-rescue grids
  315.       GdSquare- Displays Maidenhead grid squares
  316.  
  317.       cFormat - Calculates the new APRS797 Compressed Format for the 
  318.                 current position of the cursor.  This format is only
  319.                 9 bytes but is good to about 10 feet worldwide including
  320.                 all 300+ APRS symbols. (/$LLLOOOX.  X is usually a space
  321.                 unless DGPS is being used and precision to 10 feet is
  322.                 available.
  323.                 
  324.       POWER   - Displays range rings around stations showing an estimate 
  325.                 of their radio horizon based on their transmitter power, 
  326.                 height above average terrain, antenna gain and favored 
  327.                 direction.  Defaults for non reporting stations are 
  328.                 10 watts, 20 feet, and 3dB gain, omni.
  329.  
  330.       RANGE   - Displays Range Rings at 1, 3/4, 1/2 and 1/4 of the given
  331.                 range scale.  The great circle range and bearing from the 
  332.                 center to the position of the cursor is also shown.
  333.  
  334.       TRAFFIC  - Draws lines on the map between all stations sending msgs
  335.  
  336.       DFmenu   - Selects from the following DF displays:
  337.                  
  338.                  OMNI - Displays Signal strength rings around stations 
  339.                  reporting sig-strength on a fox/jammer.  Stronger sigs 
  340.                  are brighter red and null reports are black circles.
  341.  
  342.                  HEARD - Displays only DF stations reporting signal strength
  343.                  on a hidden transmitter.  See NOT-HEARD
  344.  
  345.                  NOT-HEARD- Displays DF stations reporting NO signal on the 
  346.                  fox.  These HEARD & NOT-HEARD commands are needed on B/W
  347.                  displays where color cannot distinguish the DF plots.
  348.                  
  349.  
  350. MESSAGES:  There are three types of messages in APRS.  The first is
  351. simply your one-line STATUS beacon.   New STATUS packets are highlighted
  352. in green at the bottom of all screens to show a change in status and are
  353. added to the ALL and LATEST lists.  These STATUS beacons are perfect for 
  354. alerting the net to your current status.  Secondly, APRS implements a one 
  355. line message capability between operators.  Each line is delivered
  356. sequentially and then ACKed when received by the other station.  Multiple 
  357. lines can be buffered up for eventual delivery.  This contrasts with the
  358. Mac/WinAPRS which transmit all lines at once for 5 times each, and then
  359. quit until the receiving station is heard from again.  This Mac/WinAPRS
  360. method of parallel delivery makes the lines arrive out of sequence on
  361. receipt.  
  362.     
  363.     New in 8.0 is the addition of message and bulletin Groups.
  364. The Message Groups allow you to carry on multiple-way chats with others
  365. by using GROUP callsigns.  Your message is not acked by anyone so must
  366. be killed after a few transmissions to assure it gets through and then
  367. to allow the next such line to go out...
  368.  
  369.     Bulletins are just messages sent to the call of BLN#.  Every APRS
  370. station will capture these bulletins.  You may specify a list of 
  371. Bulletin Groups, and then your station will  only capture group 
  372. bulletins you select.
  373.  
  374. MESSAGE COMMANDS:
  375.  
  376.   B - Displays current Bulletins.  To erase old bulletins, use alt-E.  
  377.       Active bulletins will re-appear if a station is still sending them.
  378.  
  379.   R - READ MESSAGES - Displays the status of your incoming and outgoing
  380.       messages.  Automatically appears when anything changes.
  381.   
  382.   K - KILL incoming message lines.  K key kills one line at a time.
  383.  
  384.   E - ERASE one outgoing line at a time.  Erases *ACKed* messages first, 
  385.       then begins prompting you for the line number.
  386.       
  387.   T - TRAFFIC - Displays the last 23 lines of message traffic monitored
  388.       between other stations. 
  389.  
  390.   S - SEND MESSAGE - Pre-loads the call of the last station you sent to.
  391.       Enter a new call for a new station.  To abort, just hit ENTER.  If 
  392.       you have hooked a station, then that stations CALL will be pre-loaded.
  393.       You may send a message to any other APRS callsign.  But there are
  394.       three special reserved calls as follows:
  395.          BLN# - Sends a temporary Bulletin where # is the line number 0-9.
  396.                 The retransmission period will decay for 20 mins and stop.
  397.          BLN@ - Sends a permanent Bltn where @ is the letters A-Z.  The
  398.                 retransmission period will decay to 20 minutes and stay.
  399.          LOG  - Is not transmitted, but is recorded on the ALL and LOG
  400.          MSG  - Is not transmitted.  Used to pre-store canned messages
  401.                 for single finger replying.  See COPY below. 
  402.          REPLY- Is not transmitted until someone sends you a message.
  403.  
  404.   F2- For REPLYING.  F2 pre-loads the callsign of the last msg received.
  405.   
  406.   MAPS-PLOTS-TRACE - This command will draw lines between stations on 
  407.       the map who are exchanging messages.
  408.  
  409.   COPY - For single key ops while mobile, you may copy a previous message 
  410.       to a new station by entering a single digit line number instead of 
  411.       message text.  The nth outgoing message will be copied to the SEND
  412.       line.  You may add additional text or hit ENTER.  You can pre-load 
  413.       "canned" messages addressed to MSG which will NOT be transmitted, 
  414.       but are available for copying to new messages.  This makes it easy 
  415.       to reply to messages while mobile with only 3 key strokes; F2, then 
  416.       the message number, then ENTER...
  417.  
  418.   VIA - You can separately route a message via a different digi path than 
  419.       your normal APRS UNPROTO path by placing a /XX on the end of the TO
  420.       call.  APRS will then attempt to use that two letter DIGIpath for
  421.       that message line.  See OPS-DIGI command.  This alt-path will get
  422.       your message out, but remember that any incomming messages TO YOU
  423.       will only get ACKS via your normal UNPROTO default path.  See 
  424.       TROUBLE.txt under NO-ACKS.
  425.  
  426.       NOTE: The channel effeciency of APRS TALK messages are no better than
  427.       normal connected packets since they also require ACK's.  Intense
  428.       real-time rag-chews on a busy APRS frequency should be done without
  429.       digipeaters or with only the exact path specified;  See the OPS-DIGI
  430.       command below, for a shortcut for rapidly changing your digi path.
  431.       The more effecient way to keyboard is to just use the OPS-COMM command
  432.       and use your TNC to connect to the other station using normal packet
  433.       over the most direct path.  The other operator MUST be at his keyboard, 
  434.       though, because APRS will time-out, erase his screen, and dump him 
  435.       back into APRS after 3 minutes of inactivity.
  436.   
  437.   ACKS:  When your MSG is acknowledged, the word *ACK* will be over printed 
  438.       on the outgoing MSG line.  Unlike normal packet, APRS does not compute 
  439.       the return path for an ACK.  Each station must set his outgoing VIA 
  440.       path so that his packets (including ACKs) get back to all stations in 
  441.       the net.  On the 2nd DUPE of an incoming message, APRS will warn you 
  442.       that the other station is probably not getting your ACKS!  APRS
  443.       will then wait 30 seconds and repeat the latest ACK once to provide a
  444.       better throughput on poor (HF and multi-digipeater) paths.
  445.  
  446.  
  447. NATIONAL TRAFFIC SYSTEM:  New in APRS 8.0 is the NTS message form and the
  448.       ability to originate NTS traffic.  To send an NTS message, simply 
  449.       use alt-N instead of the SEND command.  On receipt, to display an
  450.       NTS formatted message, simply hit the N key.
  451.  
  452. FILES MENU: This menu has all commands dealing with files.
  453.  
  454.   A - APPEND - This will permit you to load a BACKUP file without losing
  455.       all the stations that are already in your P and L lists.  If the same
  456.       calls are in the appended file as are already in memory, there will
  457.       be numerous dupes that should be manually deleted.  Also, APPEND does
  458.       not append any LOG or WHEN-HEARD data.
  459.  
  460.   D - DOS Shell - You must be in the APRS directory before you EXIT back.
  461.  
  462.   L - LOADs a backup file.  The file named BACKUP which is saved every time
  463.       you quit APRS, can be reloaded with just the initial B.  I save a
  464.       different file for each packet frequency that I monitor.  
  465.  
  466.   O - ORDER (SORT) THE L and P LISTs - Moves older stations towards page 
  467.       1 of each list, and the most recent stations to the end.  This is 
  468.       useful when the lists begin to fill, so that older stations will
  469.       be scrolled off to make room for new stations at the end.
  470.  
  471.   P - PRINT - Gives you a menu of items to route to the printer.  The
  472.       following categories may be specfied: MSGS, BLNS, POSITS, STATUS
  473.       WX and ALL.  These are printed without dupes.
  474.  
  475.   S - SAVE the current situation in a file.  If any filename other than 
  476.       the BACKUP default is entered, then APRS will also automatically 
  477.       save a LOG and Track HIStory file.  If you select NONE (or N) as 
  478.       a file name, then nothing will be saved.  This keeps you from 
  479.       writing a new BACKUP file over an older one if needed.
  480.  
  481.   R - REPLAY.  Allows you to replay track history files of past events
  482.       or any of the automatically saved track histories after they have
  483.       been saved from memory.  See details under TRACK HISTOREIS in this
  484.       file, or in the overall APRS.DOC file. ALthough only .HST files 
  485.       are shown, you can also replay .BK files from the BAKS directory
  486.       by just adding the .BK extension.
  487.  
  488.  
  489. OPERATIONS MENU:
  490.  
  491.   C - COMMS - This commmand allows you to disable APRS and talk straight
  492.       through to your TNC or GPS/WX/DF COMM port.  Use it to establish a
  493.       direct CONNECTION.  This is useful for connecting to another APRS
  494.       station's internal TNC mailbox to leave a message if he is not on line
  495.       with APRS.  Do NOT use this for sending traffic, because if there is 
  496.       no operator present at the receiving station, it will time out in 
  497.       3 minutes, and all the packets that you sent him will disappear as
  498.       APRS re-takes control.  Also permits you to monitor your other COM 
  499.       port hooked up to GPS or WX.  The F8 key will toggle your HSP 
  500.       switch for looking at the output of your GPS.
  501.  
  502.   D - DIGIPEATER PATHS -  Save up to 12 different paths for rapid recall
  503.       using only the two letter path abbreviation.  There are four other
  504.       single letter comands: 
  505.          E - ENTER a path
  506.          S - Allows you to SAVE a new TWO letter path  
  507.          L - List all paths
  508.          A - Allows you to specify up to 3 ALTERNATE paths for your posit
  509.              and status packets as a percentage of your total beacons.
  510.              These 3 paths are shown on the CONTROL-PANEL.
  511.       MESSAGES:.  When you are in QSO with one station in particular, that 
  512.       is not in your normal path, send the message /XX to force your
  513.       message packets along that route only.  Use this feature cautiously,
  514.       since APRS must allow at least 5 seconds to change the path each 
  515.       time it transmits...  and your ACKS to the same station will NOT
  516.       go that route.
  517.  
  518.   F - FIND - This command allows you to find a callsign or a gridsquare.  If
  519.       you enter the first character as a [, then APRS will asume the entry is
  520.       for a grid square.  This command works on the MAP, and P and L lists.
  521.  
  522.   Q - QUERY - This command allows you to Query the net.  A general query
  523.       asks all stations to respond with all of their STATUS, POSITS,
  524.       OBJECTS, and MESSAGES sometime in the next 2 minutes.  This command 
  525.       is AUTOMATICALLY sent when a NEWUSER starts APRS but it is not sent 
  526.       for registered users with a CONFIG file to cut down QRM.  You may 
  527.       use your cursor to indicate the location and specify a range radius 
  528.       for your Query.  You can Query individual packets from another station 
  529.       and even ask who he hears direct and what his heard log looks like for
  530.       another station.
  531.  
  532.   P - PING -  Sends out a ping packet.  If the packet is digipeated by your
  533.       selected VIA path, you will see it monitored on the bottom line of
  534.       your display.  This lets you know that your station is transmitting
  535.       and that the digipeater in your selected VIA path responded.
  536.  
  537.   S - SetRadar - This sets a collision avoidance range.  If any station
  538.       penetrates that range, then an alarm will sound.  Clear the alarm
  539.       by either hooking the station on the MAP or on the P-List.
  540.  
  541.   U - UNPROTO  Used to set up your outgoing digipeater path. (IMPORTANT!)
  542.       If you have not selected a digipeater that covers your APRS net, then
  543.       your packets and acks will never get to the other stations on freq
  544.       even though you see them fine.  YOU MUST SET YOUR VIA PATH TO COVER
  545.       your intended APRS AREA by selecting an appropriate digipeater path!
  546.       APRS will warn you if another station does not appear to be getting
  547.       your message ACKs.  Use the OPS-DIGI command to save favorite,
  548.       frequently used paths.
  549.  
  550.  
  551. INPUTS MENU:  Lets you enter your own POSITION and STATUS as well as to ADD 
  552. objects to the map.  In some of these commands, you are prompted for the 
  553. LAT/LONG of the object.  APRS pre-loads this prompt with the LAT/LONG of 
  554. the cursor.  If that position is correct, just hit ENTER.  TO change these 
  555. values, just type in a new value using as few characters as are needed to 
  556. give the resolution you need.  But you MUST always type the required 
  557. LEADING ZEROS in longitudes below 100 deg.
  558.  
  559.   A - ADD a new object to the screen at the current cursor location.  You
  560.       are prompted for all pertinent information.  There are over 50 symbols
  561.       that can be used to display the object.  Use the F1-SYMBOLS command to
  562.       see the symbols available.
  563.  
  564.   D - DIRECTION FINDING:  This command allows you to enter a beam heading or
  565.       a signal strength report for your own station during direction finding
  566.       events.  A zero (0) bearing indicates a signal strength report.
  567.       Use 360 degrees for North.
  568.  
  569.   M - MYdata:  This command lets you enter three items:
  570.         
  571.         POSIT:   Selects the current cursor position for your location.  
  572.         STATUS:  THis is your current status
  573.         HEADING: Updates your current heading (useful when stopped)
  574.         MSGgrp:  Enter your Message Groups
  575.         BLNgrp:  Enter your Bulletin Groups
  576.  
  577.   P - POWER:  Used to enter your transmitter power, height above average 
  578.       terain, antenna gain, and directivity for plotting your radio range.
  579.       
  580.   S - SAVE:  This command saves a copy of your present posit as an OBJect.
  581.       This is useful for marking special locations while you drive such
  582.       as DF fixes.
  583.  
  584.   U - UPLINK:  Identical to the SAVE command, but the object is marked for
  585.       uplinking to the net.
  586.  
  587. CONTROLS:  The C command (and TAB key) displays the control panel at the 
  588. bottom of the screen.  This two line panel shows the status of both the 
  589. SETUP and the CONTROLS.  The CONTROLS functions toggle on/off various 
  590. functions, and show your validation status and your VIA path.  Items in 
  591. lower case are OFF and upper case are ON.  Use the TAB key to get this 
  592. display:
  593.  
  594. -----------------------------------------------------------------------------
  595.  VAL | TNC | Scrnsvr | 15 | GFL| JUNK | 30/600 |dgps| RELAY |XX50| USA |BEEP|
  596. -----------------------------------------------------------------------------
  597.  XMT | LOG | UP | DR | cw | PFL| BCNS |  VHF   |FADE| VIA DIGI-1,DIGI-2        |
  598. -----------------------------------------------------------------------------
  599.  
  600.   B - BANDS.  Select HF, VHF or 2-port for KAM's.  In 2 port mode, the VHF or
  601.       HF is still the primary band, but a duplicate of all transmissions is
  602.       made on the other band.  For non-dual port TNC's, this command still
  603.       sets up the proper HF or VHF unproto paths and timing.  For KAM's the
  604.       MYAlias is set to ECHO/RELAY 
  605.   
  606.   C - CW - If CW is on, then ALL NEW STATUS beacons will be sounded in CW.  
  607.       In DX mode, CW is always on, although it can be silenced with the 
  608.       CONTROLS-CW commands.  If FREQS is turned on, then the operating 
  609.       frequency as well as the callsign will be sounded out in DX mode.  
  610.       The CW speed defaults to 15 WPM.  Other CW functions:
  611.  
  612.             E-Enable   D-Disable   F-FREQs on   S-Speed   T-Test
  613.  
  614.   D - Dead Reckoning ON/OFF
  615.  
  616.   F - FILTERS.  Toggle on/off various filters on the data:
  617.       
  618.       BCNS  - Normaly APRS only monitors UI BEACONS
  619.       DX    - Selects frequency bands for DXcluster mode
  620.       OTHER - With OTHER set on, then APRS looks at ALL packets
  621.       FADE  - on/off the fade-to-gray for contacts over 2 hours old.  
  622.               When reloading backup files of past events, FADE is turned
  623.               OFF, but after 2 hours, FADE will automatically come back on.
  624.       !FIXED- Default ON.  Filters !formatted FIXED station packets to only
  625.               the P-LIST. These stations have no STATUS anyway.
  626.       GDinTO- Parses all packets for possible GridSq in the TO address
  627.               This filter is always set in MScat, SPACE and GdSq modes
  628.       HF    - Ignores all packets from HF with GATE in their unproto path
  629.       JUNK  - Will not display any packet on the 25th line that has
  630.               embedded control characters.  THis keeps the map from scrolling
  631.               on junk from BBS's and NODES.  But it slows processging, since
  632.               every single character must be checked.
  633.       POSITIONS - This filter is normally ON to ignore the random 100 yd
  634.               error introduced by GPS.  Any posit within +/- of .04 minutes
  635.               is NOT saved to the log file.  If the filter is OFF, then all
  636.               new posits are logged except for EXACT dupes.
  637.               
  638.   G - LOG toggles on and off the automatic logging of track histories to
  639.       file.  Default is OFF to keep from filling up your LOGS directory.
  640.       When ON, and after 150 position reports, a file is automatically saved 
  641.       and memory is cleared for further accumulation.  If off, the 150 
  642.       reports are retained in memory until you QUIT.
  643.  
  644.   M - METRIC.  This command toggles between METRIC display of speeds in KPH
  645.       and temperature in CENTIGRADE.
  646.       
  647.   U - UPLINK ENABLE - When on, your objects marked for uplinking, will be
  648.       uplinked to all stations in the net.
  649.  
  650.   X - XMT ON/OFF - disables routine transmitting from your station. Useful 
  651.       for stations not actively participating in an event.  Even if XMT is 
  652.       off, however, you can still send packets with the X command and your 
  653.       station will still ACK incoming messages.
  654.  
  655.  
  656. ALT-SETUP MENU:
  657.  
  658. The SETUP menu (alt-S) has several commands plus four major sub-menus,
  659. GPS, MODES, FORMATS and OTHER.  The status of many of the SETUP options are 
  660. displayed as the top line of the CONTROLS panel:
  661.  
  662. -----------------------------------------------------------------------------
  663.  VAL | TNC | Scrnsvr | 15 | GFL| JUNK | 30/600 |dgps| MYA RELAY  | APR |BEEP|
  664. -----------------------------------------------------------------------------
  665.  XMT | LOG | UP | DR | cw | PFL| BCNS |  VHF   |FADE| VIA DIGI-1,DIGI-2        |
  666. -----------------------------------------------------------------------------
  667.  
  668.   P - POSrate - This command is used to set both the on-screen and on-air
  669.       periodicity for WX, DF and GPS reports.  The Refresh rate sets
  670.       how often the interface is sampled just to update the data on your
  671.       screen, and the POSrate value determines how often it is transmitted.
  672.  
  673.   S - SAVE CONFIG FILE -  Saves your total configuration including the 
  674.       present map display.  You will be prompted for your Validation number 
  675.       the first time only.  If you have chosen any of the GPS, DF or WX 
  676.       options, you will also be prompted for your auxilliary registration 
  677.       number as well.  You can save each CFIG file with an optional 3 
  678.       character file extension so that you can call them up quickly for 
  679.       different applications at the DOS prompt.  You invoke the optional 
  680.       files with a /XXX switch when start APRS from dos.  
  681.       
  682.       IE:  C:> APRS79/MOB would load the CFIG79.MOB file
  683.       which you saved when you operated MOBile.  etc
  684.  
  685.   T - TNCsetup - sends out TNC commands to setup the TNC for APRS.  Usually
  686.       initialized when you start, but can be done at any time, if your TNC
  687.       loses power, or needs to be reset to APRS defaults.  These commands
  688.       may be customized for  your TNC in the InitTAPR.TNC or InitAEA.TNC
  689.       SYSTEM files.  When you QUIT APRS, it restores any custom commands
  690.       that you might list in RESTORE.TNC file.
  691.   
  692.  
  693. SETUP-GPS MENU:
  694.  
  695.   ARNAV     - Configures HSP or SPM mode for ARNAV aircraft data format
  696.               or for receiving ARNAV reports over the air.
  697.   SPM       - Single Port Mode (See GPS.txt)
  698.   HSP       - Hardware single port mode (see GPS.txt)  
  699.   KLYNAS    - Sets up APRS to work with STREETS-ON-DISK (Klynas Engineering)
  700.   NMEA      - Toggles on the saving of all NMEA data to a LOGS\NMEAxxx file
  701.   OFFGPS    - Used to toggle off SPM or HSP without having to restart APRS.
  702.   PLOT      - Shows an AZ-EL plot of GPS satellites and signal strength
  703.   WAYPOINTS - Uploads POSITS via COM2 to your GPS display as waypoints
  704.   TIME-SYNC - Sync's PC clock to the next GPS report received.  This
  705.      command only sync's to the MINUTE.  Hours are not matched.  Be careful,
  706.      since many stand-alone trackers will continue to report old GPS posits
  707.      if the GPS loses lock or becomes inoperative, (car parked under a tree).  
  708.  
  709. SETUP-OTHER MENU:
  710.  
  711.       B - BEEPS Toggles nuisance BEEPS (and CW in DX mode) on and off.
  712.       L - LOCK toggles.  Prevents un authorized keyboard access to
  713.           SEND, ERASE, KILL, INPUT-ADD and WX-ENTER commands
  714.       S - SCREENSAVER toggles on/off
  715.       Z - ZONE, allows you to change  your timezone offset
  716.       G - GAME mode.  For playing chess.  Modifies APRS as follows:
  717.           * all packets are addressed to GAME instead of APRS 
  718.           * Only your LAST object is UPLINKED
  719.           * The HOOK-INS key bypasses all normal OBJ prompts
  720.           * The comment field of an uplinked object contains the move #
  721.           * Parses received GAME objects for a move number
  722.           * The move number is displayed on the map display
  723.  
  724. SETUP-DF MENU:
  725.       
  726.       D - DFSP Toggles on and off the DF single port mode
  727.       J - dfJR mode.  Configures APRS to look for both DFjr data and
  728.           GPS data on the single serial port.
  729.       M - MAGnetic Variation.  Set for your area if you will be using
  730.           magnetic DF bearings or headings.
  731.  
  732. SETUP-MODES MENU:
  733.       
  734.       N - alt-NET mode.  Allows a special function net to operate on the 
  735.       APRS frequency with other stations, but WITHOUT their packets
  736.       cluttering up everyone elses screens.  Anyone can monitor an ALTNET
  737.       by selecting this mode, OR by using the CONTROLS-FILTERS-OTHER
  738.       command to enable monitoring of all packets on frequency.  The alt-
  739.       NET command modifies APRS as follows:
  740.           * Causes APRS to send packets to ALTNET vice APRS
  741.           * ONLY looks for ALTNET packets on receive
  742.  
  743.       D - DX mode - Sets up APRS to display information for DX cluster
  744.       users.  See DX.txt.  This capability was removed in APRS800 to a 
  745.       special progarm called APRSdx.exe.
  746.  
  747.       S - Special.   Sets up a special event net on a common APRS frequency
  748.       so that the special event members only see each other without
  749.       being bothered by other traffic on the channel.  All other APRS
  750.       users, however, DO see all traffic of the special event.  This mode
  751.       modifies APRS as follows:
  752.           * Sets your transmit address to SPCL vice APRS
  753.           * Sets your APRS to ignore all packets EXCEPT those to SPCL.  
  754.           * Note, normal APRS always sees APRS AND SPCL packets.
  755.  
  756.       ZIP-LAN.  This mode allows you to connect a handfull of PC's 
  757.       together using nothing but two conductor zip cord all to one TNC.
  758.       Every station can send and receive APRS traffic to and from 
  759.       each other and on the air via the TNC.  This is a very powerful 
  760.       capability in a multi-PC environment.  See ZIP-LAN.txt.
  761.  
  762.       MASTER - In the ZIP-LAN concept, one PC has to be the master to
  763.       do handle the crosstraffic between the ZIP-LAN and the TNC.
  764.  
  765.  
  766. SETUP-FORMATS MENU:
  767.       
  768.       A - AMTOR.  Sets up for receiving AMTOR formated APRS reports
  769.           (not fully implemented for transmit yet)
  770.       
  771.       G - GRID-IN-TO.  Same as used in SPACS and MScatter modes. Useful
  772.           for shortening packet on HF.
  773.       
  774.       S - SPACE.  Sets up for sending and recording minimum length GdSq
  775.           position reports via SAREX.  See SPACE.txt
  776.  
  777.       M - Meteor scatter.  Sets up for sending minimum length GdSq reports
  778.           at a MAXIMUM transmit duty cycle.  See METEOR.txt
  779.  
  780.       N - Normal APRS.  Prompts you for a new Status beacon.
  781.  
  782.  
  783. WEATHER COMMANDS:  APRS displays weather stations as blue circles with
  784. a white line showing the wind speed and direction.  APRS uses 360 degs 
  785. for North and 000 means no direction information is available.  N is
  786. a main APRS WX hot key and the other WX commands are in WEATHER MENU:
  787.  
  788.   N - NEXT WX hot key.  Highlights the next WX station in turn with a
  789.       circle and shows the WX conditions at the top of the screen.  These
  790.       conditions will be updated on new incoming reports.
  791.   
  792.   A - ALARMS - Set alarm values on Wind, High and Low temps  and rain.  If 
  793.       a WX report exceeds these values within the range of your station, 
  794.       the station is marked on the map in RED and the screen is re-centered 
  795.       to that location.  An alarm BEEPS and the station is also marked with 
  796.       an ALARM on the P-list.  To silence the alarm, either hook/un-hook 
  797.       the reporting station on the map (ENTER-ENTER), or use the WX-ALARM-
  798.       CLEAR command.  If your own station has the automatic WX interface, 
  799.       and your conditions exceed your alarm limits, then your WX reporting 
  800.       period is reset to the minimum POSrate value, for more frequent 
  801.       reporting.
  802.  
  803.   D - DISPLAYS - Allows you to select TEMPS, WIND, RAIN or BARO pressure
  804.       to show up on the maps instead of the station CALLSIGN.  ALso lets
  805.       you select JUST-WX-ALWAYS to lock in ONLY WX stations displays.  
  806.       NWS allows you to toggle many of the APRS symbols between the 
  807.       original APRS graphics and the formal NWS symbols.
  808.  
  809.   E - Enter a manual weather report. (Will be transmitted for only 30 mins)
  810.  
  811.   L - LOG WX data.  Will cause all WX data to be saved in the TRACK HIST
  812.  
  813.   NATIONAL WEATHER SERVICE SITES - Use the MAPS-PLOTS-OVERLAYS-NWS command 
  814.       to overlay the map with all of the nearby NWS sites.  You may either 
  815.       make this temporary or add them to the P-LIST. 
  816.       
  817.   L - LOAD-NWS-DATA from a designated file for NWS hourly weather 
  818.       advisories for each NWS station listed in both the data file and 
  819.       already in your P-list.  
  820.  
  821.   Q - WEATHER QUERY - Same as QUERY, but only weather stations respond.
  822.  
  823.  
  824. TRACKING and TRACK HISTORIES - All position reports are saved to memory and
  825. eventually to file for subsequent replay.  Each new position report is checked
  826. against the last position from that unit and the current values.  If the
  827. POSITION filter is ON (default) then a new position will not be saved to
  828. track history unless movement is more than about 80 yards.  This is to reduce
  829. the number of track points for non-moving stations saved in the file.  The 80
  830. yard circle allows for most of the randomness of GPS Selective Availability
  831. so that parked vehicles do not generate a lot of packets.  If the filter is
  832. OFF, then only a single digit change in a position will generate a new
  833. position report.  ALso, when the filter is off, all DF reports are
  834. saved to file.  This makes it possible to save a DF event, or to keep
  835. historical WX data.  There are several commands related to station tracking:
  836.  
  837.    T - TRACK - a subcommand on the P-list display which allows you to
  838.        designate a station for tracking.  If TRACK is on, then the map will
  839.        always re-center on the selected station whenever it approaches a map
  840.        edge.  This re-centering anticipates the station's movements and
  841.        recenter's the map to give the best next view.
  842.  
  843.    A - ALARM - a subcommand on the P-list which allows you to set an alarm 
  844.        on a station.  If that station moves, APRS will beep and re-center 
  845.        the map to track that station.  The same filter as used on the P-list 
  846.        is also used here so that the randomness of Selective Availability 
  847.        does not unnecessarily trigger this alarm.  You can silence
  848.        the beeping by UNHOOKING the station, or by deselecting the ALARM
  849.        function.  This alarm is also used as a marker on any WX station 
  850.        reporting conditions exceeding your preset alarm values.  But since 
  851.        the WX station does not move, the Alarm will not go off again, 
  852.        unless the WX station moves!
  853.  
  854.    M - MOVE - A subcommand on the P list for moving a station.  Similar to
  855.        just hooking it with the ENTER key, but is the only way to move an
  856.        object or station with 00000/00000  for LAT/LONG.
  857.  
  858.    S - SAVE FILES - On the FILES MENU, this command forces a save of a BACKUP
  859.        a BLxxxxxx,LOG and a TKxxxxxx.HST file.  If you are in the field, and
  860.        may possibly lose power, do a SAVE now and then, to be sure you save
  861.        all track histories.  After the event, you can use a DOS text editor
  862.        to append all the track history files together for the one event.
  863.        When you Quit APRS, ONLY a Backup file is saved, the LOG and TRACK
  864.        data are LOST!  If, however, you give the BACKUP file any OTHER name,
  865.        then a LOG and TK.HST file ARE saved when you quit.
  866.  
  867.    REPLAY - Found in both the FILES and OPERATIONS MENUS.  Track histories are
  868.        retained in memory for instant replay up to 150 points.  When memory is
  869.        full, a file is automatically saved and memory cleared for more points.
  870.        If less than 150 points are in memory, you MUST MANUALLY force a save
  871.        BEFORE exiting the program or the track history points in memory will
  872.        be lost!  During Replay several commands are useful to center the
  873.        screen on the moving object, change the speed of replay and zoom in or
  874.        out, etc.  The map will AUTOTRACK a moving station if only one station
  875.        is indicated in the user response to the TRACK-which-station prompt.
  876.  
  877.  
  878. DIRECTION FINDING:  APRS can instantly traingulate fixes from many reporting
  879. packet stations, and even show overlapping signal strength contours from
  880. stations with OMNI antennas.  This new OMNI feature is a tremendous advantage,
  881. since it permits EVERYONE even without any DF equipment to participate in FOX 
  882. hunts.  APRS has serial interfaces for the Agrelo DFjr, the N7LUE Roanoak, 
  883. or the DSI Doppler unit, or it can accept manual bearings from other stations. 
  884. Even voice reported beam headings can be placed on the map by anyone using 
  885. the INPUT-ADD command and selecting the DF station symbol.  Note that APRS 
  886. uses 360 degrees as North and assumes 000 means no direction information 
  887. is available.  A quality of 8 indicates an excellent fix.  The main DF 
  888. command is in the INPUTS menu.  For more info, see DF.txt.
  889.  
  890.    SIGNAL STRENGTH - Entering 0 as a beam heading (APRS uses 360 for north), 
  891.        will indicate that the report is a signal strength report and will 
  892.        prompt you for your antenna height above average terrain and antenna 
  893.        gain.  To see the signal strength contours on the map, use the MAP-
  894.        PLOTS-DF command.  APRS will plot colored circles around each DF 
  895.        report with a brightness and a radius proportional to signal strength. 
  896.        Note that you MUST UNDERSTAND what HEIGHT-ABOVE-AVERAGE-TERRAIN means, 
  897.        for this to be useful.  If you are getting voice reports, be sure the
  898.        person is giving a true assessment of his HAAT in the general area.
  899.        Or at least in the general direction where the FOX is suspected.
  900.  
  901.    BEARING - If you enter any other bearing, APRS will prompt you for the
  902.        quality of the fix, and then will plot the bearing from your station.
  903.        heading for your station.  If you are running the WX station option,
  904.        it will be dissabled while the DF report is operative.  You may also
  905.        specify a Quality factor 1-8.  The more dotted the line is, the less
  906.        its quality.
  907.  
  908.    FADE-CIRCLE TECHNIQUE - This is a technique used by search and rescue
  909.        pilots.  It assumes that for a given receiver, there is a unique 
  910.        circle around the transmitter where the signal fades out.  If the
  911.        receiver can fly to several points where the signal just fades in
  912.        or out, then these points define a circle with the transmitter at 
  913.        the center!  APRS implements this technique with single keystroke 
  914.        operations.  Each time you press F5, a Fade point is entered on the 
  915.        map.
  916.  
  917.